●膜片聯軸器是由幾組膜片(不銹鋼薄扳1Cr18Ni9)用螺栓交錯地與兩半聯軸器聯接,每組膜片由數片疊集而成,膜片分為連桿式和不同形狀的整片式。
●膜片聯軸器靠膜片的彈性變形來補償所聯兩軸的相對位移,是一種高性能的金屬彈性元件撓性聯軸器,不用潤滑,結構較緊湊,強度高,使用壽命長,無旋轉間隙,不受溫度和油污影響,具有耐酸、耐堿、防腐蝕的特點,適用于高溫、高速、有腐蝕介質工況環境的軸系傳動,廣泛用于各種機械裝置的軸系傳動,如水泵(尤其是大功率、化工泵)、風機、壓縮機、液壓機械、石油機械、印刷機械、紡織機械、化工機械、礦山機械、冶金機械、航空(直升飛機)、艦艇高速動力傳動系統,經動平衡處理后應用于高速傳動軸系已比較普遍。
●JZMJ型重型機械用膜片聯軸器具有機械強度高、承載能力大、質量輕、結構尺寸小,傳動效率和傳動精度高、可靠性好、裝拆方便,且具有無相對滑動,不需潤滑,使用壽命長、無噪聲、耐酸、堿、防腐蝕等特點,可用于高溫、低溫和有油、有水和腐蝕介質的工況環境。適用于中、高速、大轉矩軸系傳動。以及各種機械裝置載荷變化不大的軸系傳動,通用性極強。
使用與保養
安裝前,應清洗兩軸端面,檢查端面鍵槽口等配合情況;
膜片聯軸器安裝以后,正常運轉一個班,必須檢查所有螺釘,如發現松動,必須擰緊,這樣反復幾個班,以保證不會松動;
為了防止膜片在高速運轉發生的微動磨損,導致膜片螺栓孔出現微裂而損壞,可在膜片之間涂以二硫化鉬等固體潤滑劑或對膜片表面進行減磨涂層處理;
應避免長期超載使用和操作事故的發生;
在工作運轉中,應經常檢查膜片聯軸器是否發生異常現象,如有異常現象發生必須及進維修;
在可能由于運轉的膜片聯軸器引起人身和設備事故的各個場地必須采取適當的安全防護措施。
Diaphragm coupling is by several groups of diaphragm (stainless steel thin plate 1 cr18ni9) using bolt crisscross with half coupling, diaphragm composed of several pieces fold sets in each group, the diaphragm can be divided into connecting rod type and different shapes of the chip.
Low diaphragm coupling on the elastic deformation of the diaphragm to compensate for the two axes relative displacement, is a kind of high performance metal flexible coupling components elastic, no lubrication, structure is compact, high intensity, long service life, no rotating clearance, not influenced by temperature and oil pollution, has the characteristics of acid and alkali resistance, corrosion resistance, suitable for high temperature, high speed, a shaft transmission of working condition of corrosive medium environment, widely used in all kinds of shaft transmission of mechanical device, such as the pump (especially high power), chemical pump, fan, compressor, hydraulic machinery, petroleum machinery, printing machinery, textile machinery, chemical machinery, mining machinery, metallurgical machinery, aviation (helicopters), ships high-speed power transmission system, after dynamic balancing treatment applied in high-speed transmission shafting were common.
Type low JZMJ heavy machinery with the diaphragm coupling with high mechanical strength, large carrying capacity, light quality, structure, small size, transmission efficiency and high precision, good reliability, convenient installation, and has no relative sliding, without lubrication, no noise, long service life, acid, alkali, corrosion resistance, etc, can be used for high temperature, low temperature, and the operation condition of the oil, water and corrosive medium environment. Suitable for medium, high speed, high torque shafting transmission. And all kinds of mechanical device load change not small shafting transmission, the versatility.
Use and maintenance
Before installation, two axial surfaces should be cleaned to check the mating conditions of the end keyway.
When the diaphragm coupling is installed, it is necessary to check all the screws, such as loose and must be tightened, so as to ensure it will not be loose.
In order to prevent membrane micro wear in high speed, prompted a micro cracks and damage, diaphragm bolt hole in the diaphragm between coated with solid lubricant such as molybdenum disulfide or antifriction coating treatment on the surface of a diaphragm;
Long-term overloading and operation accidents should be avoided;
During the operation, it is necessary to check whether abnormal phenomena occur in the diaphragm couplings. If abnormal phenomenon occurs, it must be repaired and repaired.
Appropriate safety precautions must be taken at various sites that may cause personal and equipment accidents due to the operating diaphragm couplings.